1-877-INSPECT

Why do many garages pose a fire hazard?

• Where are you most likely to do any welding, or any work on your car? These activities require working with all sorts of flammable materials.
• Water heaters and boilers are usually stored in garages, and they can create sparks that may ignite fumes or fluids. Car batteries, too, will spark under certain conditions.
• Oil and gasoline can drip from cars. These fluids may collect unnoticed and eventually ignite, given the proper conditions.
• Flammable liquids, such as gasoline, motor oil and paint are commonly stored in garages. Some other examples are brake fluid, varnish, paint thinner and lighter fluid.

The following tips can help prevent garage fires and their spread:

• If the garage allows access to the attic, make sure a hatch covers this access.
• The walls and ceiling should be fire-rated. Unfortunately, it will be difficult for untrained homeowners to tell if their walls are Type X fire-rated gypsum. An InterNACHI inspector can examine the walls and ceiling to make sure they are adequate fire barriers. 
• The floor should be clear of clutter. Loose papers, matches, oily rags, and other potentially  flammable items are extremely dangerous if they are strewn about the garage floor.
• Use light bulbs with the proper wattage, and do not overload electrical outlets.
• Tape down all cords and wires so they are not twisted or accidentally yanked.

If there is a door that connects the garage to the living area, consider the following:

• Do not install a pet door in the door! Flames can more easily spread into the living area through a pet door, especially if it’s made of plastic.
• Does the door have a window? An InterNACHI inspector can inspect the window to tell if it’s fire-rated.
• The door should be self-closing. While it may be inconvenient, especially while carrying groceries into the house from the car, doors should be self-closing. You never know when a fire will happen, and it would be unfortunate to accidentally leave the door open while a fire is starting in the garage.
• Check the joints and open spaces around the door. Are they tightly sealed? Any openings at all can allow dangerous fumes, such as carbon monoxide or gasoline vapor, to enter the living area. An InterNACHI inspector can recommend ways to seal the door so that fumes cannot enter the living area.

Concerning items placed on the floor, you should check for the following:

• Store your flammable liquids in clearly labeled, self-closing containers, and only in small amounts. Keep them away from heaters, appliances, pilot lights and other sources of heat or flame.
• Never store propane tanks indoors. If they catch fire, they can explode. Propane tanks are sturdy enough to be stored outdoors.

by Nick Gromicko, Ben Gromicko, Rob London and Kenton Shepard 

Most people don’t know how easy it is to make their homes run on less energy, and here at InterNACHI, we want to change that. Drastic reductions in heating, cooling and electricity costs can be accomplished through very simple changes, most of which homeowners can do themselves. Of course, for homeowners who want to take advantage of the most up-to-date knowledge and systems in home energy efficiency, InterNACHI energy auditors can perform in-depth testing to find the best energy solutions for your particular home. 

Why make your home more energy efficient? Here are a few good reasons:

• Federal, state, utility and local jurisdictions’ financial incentives, such as tax breaks, are very advantageous for homeowners in most parts of the U.S.
• It saves money. It costs less to power a home that has been converted to be more energy-efficient.
• It increases the comfort level indoors.
• It reduces our impact on climate change. Many scientists now believe that excessive energy consumption contributes significantly to global warming.
• It reduces pollution. Conventional power production introduces pollutants that find their way into the air, soil and water supplies.

1. Find better ways to heat and cool your house. 

As much as half of the energy used in homes goes toward heating and cooling. The following are a few ways that energy bills can be reduced through adjustments to the heating and cooling systems:

• Install a ceiling fan. Ceiling fans can be used in place of air conditioners, which require a large amount of energy.
• Periodically replace air filters in air conditioners and heaters.
• Set thermostats to an appropriate temperature. Specifically, they should be turned down at night and when no one is home. In most homes, about 2% of the heating bill will be saved for each degree that the thermostat is lowered for at least eight hours each day. Turning down the thermostat from 75° F to 70° F, for example, saves about 10% on heating costs.
• Install a programmable thermostat. A programmable thermostat saves money by allowing heating and cooling appliances to be automatically turned down during times that no one is home and at night. Programmable thermostats contain no mercury and, in some climate zones, can save up to $150 per year in energy costs.
• Install a wood stove or a pellet stove. These are more efficient sources of heat than furnaces.
• At night, curtains drawn over windows will better insulate the room.

2. Install a tankless water heater.

Demand-type water heaters (tankless or instantaneous) provide hot water only as it is needed. They don’t produce the standby energy losses associated with traditional storage water heaters, which will save on energy costs. Tankless water heaters heat water directly without the use of a storage tank. When a hot water tap is turned on, cold water travels through a pipe into the unit. A gas burner or an electric element heats the water. As a result, demand water heaters deliver a constant supply of hot water. You don’t need to wait for a storage tank to fill up with enough hot water.

3. Replace incandescent lights.

The average household dedicates 11% of its energy budget to lighting. Traditional incandescent lights convert approximately only 10% of the energy they consume into light, while the rest becomes heat. The use of new lighting technologies, such as light-emitting diodes (LEDs) and compact fluorescent lamps (CFLs), can reduce the energy use required by lighting by 50% to 75%. Advances in lighting controls offer further energy savings by reducing the amount of time that lights are on but not being used. Here are some facts about CFLs and LEDs:

• CFLs use 75% less energy and last about 10 times longer than traditional incandescent bulbs.
• LEDs last even longer than CFLs and consume less energy.
• LEDs have no moving parts and, unlike CFLs, they contain no mercury.

4. Seal and insulate your home.

Sealing and insulating your home is one of the most cost-effective ways to make a home more comfortable and energy-efficient, and you can do it yourself. A tightly sealed home can improve comfort and indoor air quality while reducing utility bills. An InterNACHI energy auditor can assess  leakage in the building envelope and recommend fixes that will dramatically increase comfort and energy savings.

The following are some common places where leakage may occur:

• electrical receptacles/outlets;
• mail slots;
• around pipes and wires;
• wall- or window-mounted air conditioners;
• attic hatches;
• fireplace dampers;
• inadequate weatherstripping around doors;
• baseboards;
• window frames; and
• switch plates.

Because hot air rises, air leaks are most likely to occur in the attic. Homeowners can perform a variety of repairs and maintenance to their attics that save them money on cooling and heating, such as: 

• Plug the large holes. Locations in the attic where leakage is most likely to be the greatest are where walls meet the attic floor, behind and under attic knee walls, and in dropped-ceiling areas.
• Seal the small holes. You can easily do this by looking for areas where the insulation is darkened. Darkened insulation is a result of dusty interior air being filtered by insulation before leaking through small holes in the building envelope. In cold weather, you may see frosty areas in the insulation caused by warm, moist air condensing and then freezing as it hits the cold attic air. In warmer weather, you’ll find water staining in these same areas. Use expanding foam or caulk to seal the openings around plumbing vent pipes and electrical wires. Cover the areas with insulation after the caulk is dry.
• Seal up the attic access panel with weatherstripping. You can cut a piece of fiberglass or rigid foamboard insulation in the same size as the attic hatch and glue it to the back of the attic access panel. If you have pull-down attic stairs or an attic door, these should be sealed in a similar manner.

5. Install efficient showerheads and toilets.

The following systems can be installed to conserve water usage in homes:

• low-flow showerheads. They are available in different flow rates, and some have a pause button which shuts off the water while the bather lathers up;
• low-flow toilets. Toilets consume 30% to 40% of the total water used in homes, making them the biggest water users. Replacing an older 3.5-gallon toilet with a modern, low-flow 1.6-gallon toilet can reduce usage an average of 2 gallons-per-flush (GPF), saving 12,000 gallons of water per year. Low-flow toilets usually have “1.6 GPF” marked on the bowl behind the seat or inside the tank;
• vacuum-assist toilets. This type of toilet has a vacuum chamber that uses a siphon action to suck air from the trap beneath the bowl, allowing it to quickly fill with water to clear waste. Vacuum-assist toilets are relatively quiet; and
• dual-flush toilets. Dual-flush toilets have been used in Europe and Australia for years and are now gaining in popularity in the U.S. Dual-flush toilets let you choose between a 1-gallon (or less) flush for liquid waste, and a 1.6-gallon flush for solid waste. Dual-flush 1.6-GPF toilets reduce water consumption by an additional 30%.

6. Use appliances and electronics responsibly.

Appliances and electronics account for about 20% of household energy bills in a typical U.S. home. The following are tips that will reduce the required energy of electronics and appliances:

• Refrigerators and freezers should not be located near the stove, dishwasher or heat vents, or exposed to direct sunlight. Exposure to warm areas will force them to use more energy to remain cool.  
• Computers should be shut off when not in use. If unattended computers must be left on, their monitors should be shut off. According to some studies, computers account for approximately 3% of all energy consumption in the United States.
• Use efficient ENERGY STAR-rated appliances and electronics. These devices, approved by the U.S. Department of Energy and the Environmental Protection Agency’s ENERGY STAR Program, include TVs, home theater systems, DVD players, CD players, receivers, speakers, and more. According to the EPA, if just 10% of homes used energy-efficient appliances, it would reduce carbon emissions by the equivalent of 1.7 million acres of trees.
• Chargers, such as those used for laptops and cell phones, consume energy when they are plugged in. When they are not connected to electronics, chargers should be unplugged.
• Laptop computers consume considerably less electricity than desktop computers.

7. Install daylighting as an alternative to electrical lighting.

Daylighting is the practice of using natural light to illuminate the home’s interior. It can be achieved using the following approaches:

• skylights. It’s important that they be double-pane or they may not be cost-effective. Flashing skylights correctly is key to avoiding leaks;
• light shelves. Light shelves are passive devices designed to bounce light deep into a building. They may be interior or exterior. Light shelves can introduce light into a space up to 2½ times the distance from the floor to the top of the window, and advanced light shelves may introduce four times that amount;
• clerestory windows.  Clerestory windows are short, wide windows set high on the wall. Protected from the summer sun by the roof overhang, they allow winter sun to shine through for natural lighting and warmth; and 
• light tubes.  Light tubes use a special lens designed to amplify low-level light and reduce light intensity from the midday sun. Sunlight is channeled through a tube coated with a highly reflective material, and then enters the living space through a diffuser designed to distribute light evenly.

8. Insulate windows and doors.

About one-third of the home’s total heat loss usually occurs through windows and doors. The following are ways to reduce energy lost through windows and doors:

• Seal all window edges and cracks with rope caulk. This is the cheapest and simplest option.
• Windows can be weatherstripped with a special lining that is inserted between the window and the frame. For doors, apply weatherstripping around the whole perimeter to ensure a tight seal when they’re closed. Install quality door sweeps on the bottom of the doors, if they aren’t already in place.
• Install storm windows at windows with only single panes. A removable glass frame can be installed over an existing window.
• If existing windows have rotted or damaged wood, cracked glass, missing putty, poorly fitting sashes, or locks that don’t work, they should be repaired or replaced.

9. Cook smart.

An enormous amount of energy is wasted while cooking. The following recommendations and statistics illustrate less wasteful ways of cooking:

• Convection ovens are more efficient that conventional ovens. They use fans to force hot air to circulate more evenly, thereby allowing food to be cooked at a lower temperature. Convection ovens use approximately 20% less electricity than conventional ovens.
• Microwave ovens consume approximately 80% less energy than conventional ovens.
• Pans should be placed on the matching size heating element or flame. 
• Using lids on pots and pans will heat food more quickly than cooking in uncovered pots and pans.
• Pressure cookers reduce cooking time dramatically.
• When using conventional ovens, food should be placed on the top rack. The top rack is hotter and will cook food faster. 

10. Change the way you do laundry.

• Do not use the medium setting on your washer. Wait until you have a full load of clothes, as the medium setting saves less than half of the water and energy used for a full load.
• Avoid using high-temperature settings when clothes are not very soiled. Water that is 140° F uses far more energy than 103° F for the warm-water setting, but 140° F isn’t that much more effective for getting clothes clean.
• Clean the lint trap every time before you use the dryer. Not only is excess lint a fire hazard, but it will prolong the amount of time required for your clothes to dry.
• If possible, air-dry your clothes on lines and racks.
• Spin-dry or wring clothes out before putting them into a dryer. 

Want a little straight talk on saving money and energy? Don’t believe all you have heard about ways to improve efficiency and lower heating costs. Steve Graham, Networx, says, “Even with a constant flow of information about energy efficiency, homeowners make major heating mistakes that end in higher electric bills and larger environmental footprints.” Here are 10 of those errors, with the cause and effect of each decision.

Ed Perratore, ConsumerReports.org, says: “The fed’s big retreat from the mortgage market is the latest argument for smaller-but-smarter home upgrades, especially in the kitchen. As of this October, the biggest home loans that Fannie Mae, Freddie Mac, and federal agencies will guarantee drops from more than $700,000 to as low as $271,050, according to The Wall Street Journal. That’s likely to give an added boost to lower-priced homes—and another reason to spend wisely when it comes to remodeling your kitchen. The good news: Consumer Reports’ latest tests yields a tantalizing menu of value-priced kitchen upgrades that cost as little as $1,000. Besides paying off now in improved looks and convenience, these smaller upgrades are likelier to pay bigger dividends later as home prices rebound”. Here’s his list on Yahoo.

One thing that brick chimneys, stone chimneys and fireplaces have incommon is that eventually most will require some type of maintenance to keep a water tight seal. Leaks into a chimney can cause unsafe heating equipment as well as costly damage to the chimney, the appliances connected to it, and to the building itself. Is your chimney leaking? Are you experiencing water marks on the ceiling or walls near your chimney? Is there water appearing in the firebox? Similarly, are you experiencing cracks on the exterior of the chimney which seem to keep getting bigger or are bricks actually flaking off from your chimney? Water is the common thread between all of these problems (for the most part) and following this checklist should help you to be able to arrest water infiltration or prevent further damage.

A home is robbed every 14.6 seconds and the average dollar loss per burglary is $2,119, according to statistics just released by the Federal Bureau of Investigation. And that’s the good news because burglaries were down slightly in 2010 compared to 2009. Sure you lock your doors and windows when you’re not home (you’d be surprised how many people don’t). But here are ten things that you’re probably doing that make your home a target, and what you should do instead.

10 Things That Make Your Home A Target For Thieves

Influenced by the changes in the economic and legal environments over the past 30 years, home inspection reports have changed to accommodate increased consumer expectations, and to provide more extensive information and protection to both inspectors and their clients.

HomeHints eNews is a monthly publication provided as an information resource for our clients, customers and the public in general. Feel free to read through each archived issue. If you would like to subscribe and receive each new issue via email please click on the “Contact Us” link in the menu to the right and send use your request and we will be happy to add you to our mailing list.

Click here to visit HomeHints eNews